“HMAS Australia 澳大利亚”号 - 场景模型

old_cobra

HMAS Australia
by Min Hin Chong

1/700 HMAS Australia (Combrig)

The model depicts the Australia as she appears in 1941.

The following modifications were made to the kit:

    * Deletion of 20 mm gun tubs on turrets, fantail and bridge wings. The Australia did carry these weapons, but I couldn't work out their location on the photos of the ship in this time period.
    * Replacement of resin anchors with PE anchors from Tom’s Modelworks
    * Moulded on anchor chains removed and replaced with miniature chain
    * Doorway cut into breakwater
    * Periscopes added to main gun turret cheeks from strip styrene
    * Main gun barrels replaced with turned metal items from Clipper Models
    * Multiple Deck vents added to main deck, scratch built from styrene rod
    * Multiple photo-etch doors, ladders and hatches added to superstructure
    * Bridge wing supports scratch built from styrene and photo-etch from White Ensign Models
    * Details such as binoculars and compass from the spares box added to open bridge.
    * Splinter mattresses scratch built form styrene and added to upper bridge level, area behind main mast and director tower
    * Masts constructed from brass wire. WEM PE added
    * Type 286 radar added to mainmast from Tom’s Modelworks PE set
    * Scratch built searchlight platforms adjacent to fore funnel. Searchlights from the spare’s box
    * Ammo boxes from spares box added to main deck.
    * Additional pair of ship’s boat’s added from spare’s box.
    * Photo-etch boat chocks and oars from White Ensign Models added to boats.
    * Splinter shields around 4 inch AA mounts scratch built from styrene
    * Vision slit covers added to 4 inch AA turrets
    * Whistle platform added to fore funnel from White Ensign Models
    * Funnel piping redone with styrene rod
    * Funnel cap grills modified from White Ensign Models PE
    * Cranes scratch built from Styrene tube, resin and PE from White Ensign Models (Those cranes are huge, I used 1/600 Repulse PE cranes!)
    * Torpedo tube housing scratch built form styrene
    * Aircraft catapult from White Ensign Models PE.
    * Walrus aircraft from Trumpeter. White Ensign Models PE added.
    * Pompoms replaced with resin and photo-etch from White Ensign Models
    * Aft Search light platforms constructed from WEM PE. Searchlight from the spares box.
    * Boat davits from Hasegawa PE.
    * PE railing from White Ensign Models.
    * Ship and aircraft rigged with paintbrush bristles for heavy cable and Uni-Caenis fly tying line for finer lines.

“HMAS澳大利亚”号

制作者：Min Hin Chong
比例：1/700
套材：Combrig

该模型描述了澳大利亚，她在1941年现身。

下面是对模型套材的修改：

     * 删除了20毫米炮炮塔上的盆，船尾甲板和桥翼。“澳大利亚”号没有携带这些武器，但是在这段时间我无法解决他们在船的照片上的位置。
     * 用Tom’s Modelworks的蚀刻锚更换了树脂锚
     * 去掉模制的锚链，取而代之的是小链条
     * 通道切割成防波堤
     * 潜望镜添加到主炮塔两侧的塑料带
     * 主炮管改为Clipper Models的金属件
     * 多个舱口添加到主甲板上，用苯乙烯棒自制的
     * 多个蚀刻的门、梯子和舱口添加到上层建筑上
     * 桥式支架用苯乙烯和White Ensign Models的蚀刻片自制的
     * 配件盒里的望远镜和指南针等细节添加到敞开的舰桥上
     * 分裂床垫用苯乙烯自制并加到舰桥梁上层，主桅和主塔后面的地方
     * 桅杆用铜丝制作，添加WEM的蚀刻件
     *  Tom’s Modelworks的蚀刻件，286型雷达添加到主桅上
     * 自制的探照灯平台毗邻前烟囱，探照灯是配件盒里的
     * 把配件盒里的弹药箱添加到主甲板上
     * 把配件盒里的附加的一对小艇加上
     * 把White Ensign Models蚀刻船垫和桨增加船上
     * 用苯乙烯自制分裂盾周围的4英寸机炮组合座
     * 观测窗盖添加到4英寸机炮塔上
     * White Ensign Models的汽笛平台添加到前烟囱
     * 烟囱用苯乙烯棒装饰
     * 烟囱罩格栅用White Ensign Models的蚀刻件改进
     * 用苯乙烯管材，树脂和White Ensign Models的蚀刻件自制起重机（这些起重机是巨大的，我用1/600 Repulse蚀刻起重机！）
     * 用苯乙烯自制鱼雷发射管罩
     * 飞机弹射器是White Ensign Models的蚀刻件
     * 号手的海象飞机加White Ensign Models的蚀刻件
     *  对空速射炮用树脂和White Ensign Models的蚀刻件取代
     * 后部探照灯平台用White Ensign Models的蚀刻件制作，探照灯是配件盒里的
     * 吊艇杆是长谷川的蚀刻件
     * 蚀刻的栏杆是White Ensign Models的
     * 船舶和飞机的牵索用画笔刷毛来体现沉重感，而旗线用细线条。

old_cobra

[fbdsbsb] [fbdsbsb] [fbdsbsb]

aucmaswcw

[vse4bb]改造的干净利落，好手艺[fbdsbsb]